Reset Procedure

  1. Press and hold the down button in until the unit reaches Its lowest height.
  2. Release the down button.
  3. Press and hold the down button again until the LED displays reads ASR
  4. Release the down button.
  5. Press and hold the down button again until the desk lower’s a little bit more, slightly rises and stops.
  6. Release the down button, your desk is now ready to use.

Changing Inches to Centimeters

  1. Press the down button on the handset until the unit reaches It’s lowest position.
  2. Press and hold the down button again until the LED reads “ASR”.
  3. Press and hold the 2 button (about 5 seconds) while the LED flashes “ASR” and then switches to either: 10.3=cm 10.4=inches.
  4. Release the 2 button.
  5. Press and hold the 2 button again until the desired setting is reached.
  6. Once the chosen setting is displayed, release the button and wait about 5 seconds for the display to return to ASR.
  7. Finish the reset process by pressing and holding the down button until the desk lowers a little bit more, slightly rises and stops.
  8. Release the button. The new measurement setting is saved and your desk is now ready for use.

Setting Upper and Lower Limits

To set upper limit press the up button till the desired height…

  1. Press M button
  2. Press up button in till handset says 999

To set lower limit press the down button till the desired height…

  1. Press M button
  2. Press down button in till handset says 000

To clear your upper and lower limits…

  1. Make sure the desk isn’t in an upper or lower preset height.
  2. Press the M button till you see a 5 on the handset, then release.
  3. Press and hold the M button till you see 555
  4. You have now cleared your upper and lower limits.

One Touch

  1. Press and hold the down button till the desk reach’s it’s lowest position, then let go of button.
  2. Press and hold down button till handset reads RST then let go of the button.
  3. Press and hold the 1 button in for 5 seconds till you see 10.2.
  4. Press the down button so it switches to 10.1.
  5. Press and hold the down button till the desk gives a soft bump and returns to 22.0 or 27.0.
  6. You can now program your heights and with one touch the desk will raise and lower.

Setting The Retracted Height

  1. Press the down button on the Handset till the unit reaches It’s lowest position.
  2. Measure the distance from the floor to the bottom of the worksurface.
  3. If the number on the LED display doesn’t match your measurement, follow these steps.
  4. Press and hold the down button until the unit displays ASR.
  5. Press and hold the M button for 5 seconds till the handset displays the flashing height.
  6. Use the up/down buttons to change the value of the starting height so that it matches your measurement.
  7. Wait about 5 seconds till the hadset displays ASR.
  8. Finish the reset process by pressing and holding the down button again until the desk lowers a little bit more, slightly rises and stops. Release the button. The new starting height is saved, and your desk is now ready to use.

Locking the Handset

To Lock the Handset:

  • Press and hold the M button on the Handset for about 10 seconds until the LED displays S and then to “LOC” release the button.

To Unlock the Handset:

  • Press and hold the M button on the Handset for about 10 seconds until the LED switches from “LOC” to the height display. Release the button.

Changing Anti-Sensitivity Collision

  1. Press the down button in until the unit reaches its lowest position.
  2. Press and hold the down button in until the LED display reads ASR.
  3. Press and hold the up button (about 5 seconds) while the LED displays “ASR” and then switches to either:
    1. 10.5 = 10 kg. pressure (most sensitive)
    2. 10.6 = 15 kg. pressure (middle setting)
    3. 10.7 = 20 kg. pressure (least sensitive)
  4. Release the up button.
  5. Press and hold the up button again until the desired setting is reached.
  6. Once the chosen setting is displayed, release the button and wait about 5 seconds for the display to return to ASR.
  7. Finish the reset process by pressing and holding the down button until the desk lowers a little bit more, slightly rises and stops.
  8. Release the button.
  9. The new Anti-Collision sensitivity setting is saved and your desk is now ready to use.
StableRise kiosk

Contact Us

Find out for yourself by calling